I ran a simple 3D model with symmetry boundary conditions first using elastic material and then as hypoplastic using a subroutine. However, in the former case, I don’t get the above warning and the job was completed. When I use the UMAT, I got warning of 197 unconnected regions and my job aborted. I don’t know whether unconnected regions is the reason for the job abortion; but I’m inquisitive to know the reason behind this warning considering it did not appear for the elastic case.
Tags: ABAQUS modelingABAQUS modeling: Warning about unconnected regions when using hypoplasticity subroutine
Related Articles
-
DIANA with monopile follows Blum theory saving 10 m of length
Ab van den bos||Finite Elements|0 |
Views 2,785
Where the client was forced to make all his horizontal loaded Dolphins (piles) 10 m longer we could trustworthy proof that this actually was not necessary saving millions of cost […] -
FE formulation and software
Mark G||Finite Elements|0 |
Views 1,112
Hi, I am looking for advice on FE formulation and software. I am a recent graduate of MSc Geotechnical Engineering and am looking to do freelance work or possibly undertake […] -
Slope stability calculation with hypoplasticity using phi-c reduction available now in download section
David Mašín||Finite Elements|0 |
Views 3,219
The strength reduction method in clay hypoplasticity now available -
An error in the SANISAND umat runtime
Zhentao Liu||Finite Elements|15 |
Views 1,116
Dear all I was simulating a pile in a fully drained soil subjected to horizontal loads using ABAQUS (as shown in Figure 1) and noticed from the monitor that the […] -
hypoplasticity model with Abaqus umat on Brno clay
mahdie masoudi||Finite Elements|5 |
Views 3,326
Dear all, I am a Ph.D. student at Kharazmi University. Recently I have been trying to simulate a triaxial compression test using the hypoplasticity model for clay using ABAQUS. The […] -
Special issue of Computers and Structures “Numerical simulation of multi‐physics phenomena in geotechnical structures”
David Mašín||Finite Elements|1 |
Views 5,086
https://www.sciencedirect.com/journal/computers-and-structures/about/forthcoming-special-issues Numerical simulation of multi‐physics phenomena in geotechnical structures Complete and thorough analysis of geotechnical structures, requires various complex materials models with internal structures, which cannot be described by the […] -
Tochnog Professional 100 element free version, www.tochnogprofessional.nl
dennis roddeman||Finite Elements|0 |
Views 3,009
The Tochnog Professional finite element program is now available as free version with 100 elements. It can be downloaded without registration from http://www.tochnogprofessional.nl. Several commercial and free pre- and postprocessors […] -
Consolidation analysis using HP clay model in Plaxis
muhammad shakeel||Finite Elements|1 |
Views 3,421
Dear Prof David / SOil model community, I am performing coupled consolidation analysis for deep excavation in clay using HP clay model in Plaxis 3D. Performing the undrained analysis, the […]
0 Comments
Who is Online
No one is online right now
Search SoilModels Website
Recent posts
-
Presentations from Prague Geotechnical Days 2023 including 29th Prague Geotechical Lecture by Yannis Dafalias 25.5.2023
-
Problem in using Hypoplastic model for sand in Abaqus. 17.5.2023
-
An error in the SANISAND umat runtime 8.5.2023
-
Htypoplastic Model in Miidas GTS NX 25.4.2023
-
set cavitation limit in ABAQUS/STANDARD when using SANISAND umat 2.4.2023
-
FE formulation and software 25.3.2023
-
Multi-objective analysis of the Sand Hypoplasticity model calibration 24.3.2023
-
Problem with SANISAND UMAT 7.3.2023
-
Prague Geotechnical Days 2023 (22nd – 23rd of May) with Prague Geotechnical Lecture by prof. Yannis Dafalias 28.2.2023
-
What is an appropriate damping model for dynamic liquefaction analysis of tailings storage facility in FLAC? 10.2.2023
-
Abaqus vs Plaxis – Local Convergence Tolerances 2.2.2023
-
Zbraslav sand – Cyclic tests by Charles University 17.1.2023
Recent Comments
- Francisco Mendez on Presentations from Prague Geotechnical Days 2023 including 29th Prague Geotechical Lecture by Yannis Dafalias
- Héctor Montenegro on Extended Mohr–Coulomb (EMC)
- Kassem Dib on Problem in using Hypoplastic model for sand in Abaqus.
- Isma Khabis on Problem in using Hypoplastic model for sand in Abaqus.
- Isma Khabis on Problem in using Hypoplastic model for sand in Abaqus.
- Kassem Dib on Problem in using Hypoplastic model for sand in Abaqus.
- Zhentao Liu on An error in the SANISAND umat runtime
- Arie Koot on An error in the SANISAND umat runtime
- Zhentao Liu on An error in the SANISAND umat runtime
- Arie Koot on An error in the SANISAND umat runtime
- Zhentao Liu on An error in the SANISAND umat runtime
- Arie Koot on An error in the SANISAND umat runtime
- Zhentao Liu on An error in the SANISAND umat runtime
- Arie Koot on An error in the SANISAND umat runtime
- Zhentao Liu on An error in the SANISAND umat runtime
- Zhentao Liu on An error in the SANISAND umat runtime
- Zhentao Liu on An error in the SANISAND umat runtime
- Zhentao Liu on An error in the SANISAND umat runtime