Dear all,
I am pretty new in coding and using Abaqus. I have trouble with coding the UMAT for NorSand. If any of you have any good references, please share with me. Feel free to give me advises.
Thanks,
Shile
UMAT for NorSand
Related Articles
-
Problems with the UMAT subroutine check_parms_DM of the SANISAND constitutive model
meng xiaowei||Constitutive Modelling|3 |
Views 422
Where can I find the source of the content in the picture below in the UMAT subroutine check_parms_DM of the SANISAND constitutive model? -
Question on the Matlab driver – model hypo Sand
c sx||Constitutive Modelling|1 |
Views 162
As a beginner to soil constitutive modelling, I am learning the hypoplastic models by reading the matlab drivers. I am confused with the matlab file f_hyp.m in the model hypo_sand. […] -
Hypo-sand UMAT problem
sobhan abedinnejad||Constitutive Modelling|1 |
Views 350
Dear community I have 4 Question in implementation of Hypo-sand Umat in ABAQUS could someone kindly explain? 1. I checked the Umat file from (https://soilmodels.com/download/plaxis-umat-hypoplas-zip/) and i understand this subroutine […] -
Clay Hypoplastic Model ABAQUS UMAT
Hashmi Sohawon||Constitutive Modelling|3 |
Views 484
Hi, I wanted to ask if the variables/parameters defined in the online Hypoplastic model manual for PLAXIS (https://web.natur.cuni.cz/uhigug/masin/plaxumat/node6.html) are the same for the ABAQUS UMAT? -
K0 determination Reloading using HP clay model
muhammad shakeel||Constitutive Modelling|0 |
Views 141
Hi Prof. Masin , It is related to my previous post. Sorry to bother you again. I simulated Oedometer test in Plaxis as well as centrifuge reloading (using HP clay […] -
Calibration of Hypoplastic material model parameters
Amine Aboufirass||Constitutive Modelling|6 |
Views 621
I would like to derive material parameters based for a simulation which will implement the hypoplastic material model based on the following information: • Heavily overconsolidated • Very dense, fine […] -
CEL analysis using hypo plasticity Vumat
abd Elfattah||Constitutive Modelling|8 |
Views 895
Greetings i used interface Vumat with Umat for simulating CEL problem, after 50% of analysis, i got the error as “Excessive incremental rotation of the elements in element set ” […] -
Undrained Tests with Basic Clay Hypoplasticity
Hashmi Sohawon||Constitutive Modelling|6 |
Views 505
Hi Prof. David, I have obtained these results in that attached picture using Triax and got confused when seeing that an isotopically normally consolidated sample does not follow a trend […]
0 Comments
Who is Online
No one is online right now
Search SoilModels Website
Recent posts
-
K0 determination Reloading using HP clay model 22.2.2021
-
Seismic Liquifaction 11.2.2021
-
Modelling cyclic loads in Tochnog 11.2.2021
-
Soft soil model vs Soft soil creep model 8.2.2021
-
Boundary value problems for granular materials subjected to earthquake loading 8.2.2021
-
Guidance for a newbie 6.2.2021
-
Modelling Rate-dependent behaviour of clay [Urgent] 1.2.2021
-
Postdoctoral Fellowship in computational geomechanics 27.1.2021
-
USDM – Creep -SCLAY1S 25.1.2021
-
Hardening Soil Model in Abaqus 25.1.2021
-
Effects of water content in sand in hypoplastic strength parameters 25.1.2021
-
Simulating Oedometer test in PLAXIS 24.1.2021
Recent Comments
- David Mašín on Kadlíček, T. and Mašín, D. (2020). The strength reduction method in clay hypoplasticity. Computers and Geotechnics (in print)
- Mehdi Joneidi on Kadlíček, T. and Mašín, D. (2020). The strength reduction method in clay hypoplasticity. Computers and Geotechnics (in print)
- Micha Van der Sloot on PM4Sand for Plaxis Download
- Eduardo Muguet on PM4Sand for Plaxis Download
- Sudipta Bhowmick on Subroutine of SANISAND model
- Sudipta Bhowmick on SANISAND (Dafalias and Manzari, 2004)
- Osama Dar on Guidance for a newbie
- Arie Koot on Seismic Liquifaction
- Emrecan Güven on Guidance for a newbie
- Osama Dar on Guidance for a newbie
- Gertraud Medicus on Guidance for a newbie
- Juan Tello on Clay hypoplasticity with strength reduction (umat and Plaxis dll).
- Juan Tello on UMAT Implementation of Sand Hypoplasticity by UIBK
- Micha Van der Sloot on PLAXIS
- Micha Van der Sloot on USDM – Creep -SCLAY1S
- Arie Koot on Hardening Soil Model in Abaqus
- Balaji Bandaru on Simulating Oedometer test in PLAXIS
- Ayzukra Ablimit on Simulating Oedometer test in PLAXIS