“A hypoplastic relation for granular materials with a predefined limit state surface” paper by P. A. Von Wolffersdorff April 1996 include a triaxial test result of sample 10cm diameter and length. The Hochstetten sand properties are assigned screenshot is attached below and Meshing of the sample by standard linear C3D8 brick element. Two steps of static general are created. step 1 confining pressure of 200 kPa and step 2, shearing stage applied displacement of 1cm by creating 10 second time step (1mm/sec loading rate). After the analysis completed the stress S33 in Z direction after shearing not generated. stresses are same as during confining stage in S11, S22 and S33 even after 1cm displacement of the soil sample.
Difficulties in calibration of triaxial test on Hochstetten sand by sand Hypoplasticity model
Related Articles
-
Calibration the UMAT sand hypoplastic parameters
aysar hassan||Constitutive Modelling|3 |Views 4,043
Dear all, I’m facing trouble in calculating NO. 16 parameter in the UMAT for sand hypoplasticity by Dr. Masin, any help will be really appreciated especially with an example. Best […] -
Htypoplastic Model in Miidas GTS NX
Kassem Dib||Constitutive Modelling|6 |Views 2,314
Hello.. I am defining the hypoplastic parameters for Karlsruhe sand (found in a paper) using MIDAS GTS NX. In the software the a requesting (in addition of parameters) the number […] -
Question on the Matlab driver – model hypo Cam Clay
Hengyi Kang||Constitutive Modelling|2 |Views 4,027
As a beginner to soil constitutive modelling, I am learning the hypoplastic models by reading the matlab drivers. I am confused with the matlab file f_hyp.m in the model hypo_camclay. […] -
Question on the Matlab driver-hypoplastic models
c sx||Constitutive Modelling|5 |Views 3,969
Dear all, After carefully reading the matlab drivers of hypoplastic models, I was wondering why there is not mix control undrained TX compression. I want to achieve the same result […] -
need help in Flac3d6
Ahmed Mahir||Constitutive Modelling|0 |Views 4,128
dear user hello i intend to build a numerical model using flac3d 6 software i build the geometry with extrusion pane and set all values for pile – soil interaction […] -
Modelling Rate-dependent behaviour of clay [Urgent]
Balaji Bandaru||Constitutive Modelling|0 |Views 3,880
Using PLAXIS, how to model rate dependent behavior of clay. This is to show the viscous behavior of the soil. Thank you in advance -
sand liquefaction modelling in Anura3D
Daniel Brox||Constitutive Modelling|0 |Views 512
Beginner level question for this forum – Trying to replace a Mohr-Coulomb model of sand in an Anura3D simulation with a material model which accurately describes sand liquefaction. References I’ve […] -
Combining Hypoplastic-sand and Hypoplastic-clay in one UMAT file
anis kheffache||Constitutive Modelling|0 |Views 3,793
Hi everyone, i have combined both Hypoplastic sand and clay umats in one umat ( to use for example in the case of multilayered soil medium made of clay and […]
Who is Online
No one is online right now
Search SoilModels Website
Recent posts
- Degradation ( disturbance ) of hypoplastic clay 23.4.2024
- Degradation ( disturbance ) of hypoplastic clay 23.4.2024
- Paper of Coulomb, C. A. (1773) 15.4.2024
- ABAQUS UMAT of hypoplastic clay model 6.4.2024
- Prague Geotechnical Days 2024 “Geotechnical monitoring” and 30th jubilee Prague Geotechnical Lecture by prof. Eduardo Alonso 5.4.2024
- UMAT for Creep-SCLAY model. 1.3.2024
- Cyclic tests with Triax element test driver 14.2.2024
- SUMMER SCHOOL ‘Numerical Modelling in Geotechnical Engineering’, Innsbruck – July 22nd-26th, 2024 1.2.2024
- COURSE IN SOIL MODELING – NTNU, Trondheim – October 14th to 18th, 2024 21.12.2023
- MSE walls design in Plaxis 11.12.2023
- sand liquefaction modelling in Anura3D 8.12.2023
- BCV bentonite experimental and modelling datasets 14.11.2023
Recent Comments
- Debdip Das on SANISAND Abaqus UMAT and Plaxis implementations
- Ramon Varghese on SANISAND for FLAC3D Download
- Akhtyar Gul Shirzoi on ABAQUS UMAT of hypoplastic clay model
- KHA DIDJA on Animating Soil Models
- Jh Xue on Undrained Tests with Clay Hypoplasticity Intergranular
- Zhentao Liu on Problem in simulating CPT using SANISAND04
- Gertraud Medicus on ABAQUS UMAT of hypoplastic clay model
- Chen Zhiming on Download Package of Charles University Implementation of High Cycle Accumulation Model
- Konstantinos Chatzis on Cyclic tests with Triax element test driver
- Abhay Pratap Singh on Cyclic tests with Triax element test driver
- Giovanni Ciardi on Cyclic tests with Triax element test driver
- Konstantinos Chatzis on Cyclic tests with Triax element test driver
- Ismail Khan on Cyclic tests with Triax element test driver
- Kanika Lamba on Cyclic tests with Triax element test driver
- Arie Koot on How to model the settlement in soil due to water drawdown.
- Konstantinos Chatzis on Cyclic tests with Triax element test driver
- Jose Duque on Cyclic tests with Triax element test driver
- MohamadReza Kamali on How to model the settlement in soil due to water drawdown.
Hi Akshay, it seems to me that you assign Par15 to very high value. Par15 is bulk modulus of water to be used exclusively in undrained analysis using penalty method. As you apply undrained condition during compression stage, effective stress will not change. Can you try to set Par15=0 and rerun? Please check Statev8, which is pore water pressure, and calculate the effective stresses yourself as total stress (Abaqus output) minus pwp. Regards David
Dear Dr. David Mašín
also i am facing this problem when generate intergranular strain parameters with setting Par15=0. but no problem when turn off intergranular strain parameters.
Regards