Dear all, I am a PhD student in Hohai University. Recently I have been trying to simulate a triaxial compression test using the hypoplasticity model for clay. The UMAT subroutine is provided by Pro Masin on this website (umat_hcea.for). Figure 1 shows the parameters that I set in the model based on the link ‘https://web.natur.cuni.cz/uhigug/masin/plaxumat/node6.html’, but there is no result or error in the calculation, as shown in Figure 2. Could you please tell me what is the possible reason for this problem?
Tags: clay hypoplasticity; abaqus; umata question on the clay hypoplasticity model with Abaqus umat
Related Articles
-
Transient Dynamic analysis (U-P formulation)
anis kheffache||Finite Elements|4 |Views 4,123
Hi everyone, i want to carry out some transient dynamic analysis. as far as I know, dynamic steps in abaqus does not allow for pore pressure build-up and dissipation, and […] -
Hypoplastic model for clays in a Plaxis 2D simulation – Problem
Daniel Valencia||Finite Elements|2 |Views 3,274
Hello everybody, Using Hypoplastic model for clays, with intergranular concept parameters, I am simulating a simple oedometer test, phase by phase, using a dummy layer on the top of the […] -
Vibration foundation behavior
Naif Alsanabani||Finite Elements|0 |Views 4,611
Dear all I have FEM analysis results for vibration foundation response that rested either on saturated salt-encrusted flat soil (case-1) or on finite cemented sand overlie saturated salt-encrusted flat soil […] -
Few more Question on calculating lateral displacement of pile using hypoplastic clay model
Muhammad Ahmad||Finite Elements|0 |Views 3,871
Dear Professor David, Thank you very much for your previous clarification. its really helps. In continuation to my previous , there are few more question, i want your kindself to […] -
A problem of convergence from using Hypoplastic model in Abaqus
Joe Chu||Finite Elements|5 |Views 3,665
Dear all, The sand hypoplastic model has been used to simulate the interaction between soil and pile. However, there is a bad convergence in the process of calculation. When I […] -
DIANA with monopile follows Blum theory saving 10 m of length
Ab van den bos||Finite Elements|0 |Views 3,322
Where the client was forced to make all his horizontal loaded Dolphins (piles) 10 m longer we could trustworthy proof that this actually was not necessary saving millions of cost […] -
hypoplasticity models in free Tochnog Professional
Silvia Imposimato||Finite Elements|0 |Views 3,614
In this post we will list built-in hypoplasticity formulations in the free Tochnog Professional program. Since these hypoplasticity options are built-in there is no need to link external umat routines. […] -
EasyTochnog input file generator
Dennis Roddeman||Finite Elements|0 |Views 3,359
Hi All, Tochnog Professional now has an EasyTochnog extension, see http://www.tochnogprofessional.nl/easy_tochnog/page.php. With simple input data like pile diameter, pile length, slope geometry, sheet pile data, etc. a complete Tochnog Professional […]
Who is Online
No one is online right now
Search SoilModels Website
Recent posts
- Degradation ( disturbance ) of hypoplastic clay 23.4.2024
- Degradation ( disturbance ) of hypoplastic clay 23.4.2024
- Paper of Coulomb, C. A. (1773) 15.4.2024
- ABAQUS UMAT of hypoplastic clay model 6.4.2024
- Prague Geotechnical Days 2024 “Geotechnical monitoring” and 30th jubilee Prague Geotechnical Lecture by prof. Eduardo Alonso 5.4.2024
- UMAT for Creep-SCLAY model. 1.3.2024
- Cyclic tests with Triax element test driver 14.2.2024
- SUMMER SCHOOL ‘Numerical Modelling in Geotechnical Engineering’, Innsbruck – July 22nd-26th, 2024 1.2.2024
- COURSE IN SOIL MODELING – NTNU, Trondheim – October 14th to 18th, 2024 21.12.2023
- MSE walls design in Plaxis 11.12.2023
- sand liquefaction modelling in Anura3D 8.12.2023
- BCV bentonite experimental and modelling datasets 14.11.2023
Recent Comments
- Akhtyar Gul Shirzoi on ABAQUS UMAT of hypoplastic clay model
- KHA DIDJA on Animating Soil Models
- Jh Xue on Undrained Tests with Clay Hypoplasticity Intergranular
- Zhentao Liu on Problem in simulating CPT using SANISAND04
- Gertraud Medicus on ABAQUS UMAT of hypoplastic clay model
- Chen Zhiming on Download Package of Charles University Implementation of High Cycle Accumulation Model
- Konstantinos Chatzis on Cyclic tests with Triax element test driver
- Abhay Pratap Singh on Cyclic tests with Triax element test driver
- Giovanni Ciardi on Cyclic tests with Triax element test driver
- Konstantinos Chatzis on Cyclic tests with Triax element test driver
- Ismail Khan on Cyclic tests with Triax element test driver
- Kanika Lamba on Cyclic tests with Triax element test driver
- Arie Koot on How to model the settlement in soil due to water drawdown.
- Konstantinos Chatzis on Cyclic tests with Triax element test driver
- Jose Duque on Cyclic tests with Triax element test driver
- MohamadReza Kamali on How to model the settlement in soil due to water drawdown.
- Leo Alibert on MSE walls design in Plaxis
- Ignacio Zuloaga on MSE walls design in Plaxis
it does not look like a warning of hp_umat.
it’s probably from another abaqus material
yeah, I set another material in this model that led to this warning which disappeared after deleting this material .
Hi Tao Zhu, try to define 20 material-parameters instead of 29 (for PLAXIS) and 16 state-variables (depvar). I already have used this model with Abaqus. The model was running perfectly.
Thanks for your advice. I have defined 20 material-parameters instead of 29, but it doesn’t work and the error is ‘User subroutine umat is missing’. There should be no problem with the path of the user subroutine file. Could you please tell me what is the possible reason for this problem?
I read the umat subroutine ‘umat_hcea.for’ and I think the number of the material-parameters should be 22—alpha_power=parms(21),avoid=props(22).
However the sand model with ‘umat.for’ can run perfectly… I’m really confused that the clay model aborted with the error ‘User subroutine umat is missing’ but the sand model can run successfully.
Dear Tao,
I guess the issue is simply to solve. Open the umat_hcea.for with your favorite text/code editor and change the name from ” subroutine umat_hcea(…” to ” subroutine umat(…”.
best regards,
Hans
Dear Hans, Thank you very much! It really works!