Dear concern,
Recently i have modelled the soil pile interaction using Abaqus CEL method. The hypoplastic behavior of the soil is model using user subroutine VUMAT. The properties of the hypoplastic sand are attached. Thanks to Dr. David Mason and all other who have contributed in developing this user subroutine along with explicit interface.
i have applied an initial stress field of 0.17 MPa and the vertical length of the soil model is 9.5 meter. An initial vertical displacement of 2. meter is applied to the pile with step time of 1 sec. in in the next phase a load of 250 KN is applied with step time of 0.1 sec. The the problem is the stress on the soil around the pipe start decreasing as the pile touches the soil and then gradually reduced to zero. The vertical displacement is applied using 50 stress increments,.
The problem is the soil elements around the pile cannot withstand the load and deformed excessively. Is this issue related to my material properties or vertical length of the model is not enough to support the initial vertical consolidation. i have attached the picture of sand deformation. Waiting for the kind assistance. Thank you
Interpreting results of sand hypoplastic model with Abaqus VUMAT
Related Articles
-
How can I solve the error in Abaqus mentioned below?
Sudipta Bhowmick||Constitutive Modelling|19 |Views 6,245
I am using SANISAND to simulate a triaxial compression test under monotonic loading. But every time my simulations break and give the same message “Abaqus/Implicit Packager exited with an error […] -
Question on the Matlab driver-hypoplastic models
c sx||Constitutive Modelling|0 |Views 4,088
Dear all, After carefully reading the matlab drivers of hypoplastic models, I was wondering whether the driver can simulate triaxial extension tests. As I change the constraints to reflect triaxial […] -
UMAT for strain-rate effects
Luis Zambrano-Cruzatty||Constitutive Modelling|0 |Views 3,962
Dear community, I’m interested in constitutive models that can handle strain-rate effects for HSR on sands for simulating free fall penetration. I would appreciate any help. Do you know any […] -
SImulation with hypoplastic model for granular materials in ABAQUS
yusheng yang||Constitutive Modelling|2 |Views 4,404
Hello, I want to use the hypoplastic model for granular materials downloaded from https://soilmodels.com/download/plaxis-umat-hypoplas-zip. The UMAT file umat.for is the model for sand. I followed the instruction https://web.natur.cuni.cz/uhigug/masin/plaxumat/node5.html. I have […] -
Papers on Excalibre
David Mašín||Constitutive Modelling|0 |Views 4,481
Hi all, Details of Excalibre software (https://soilmodels.com/excalibre) functionality and calibration procedure have been published in two papers, which are now available online at the webpages of publisher (https://link.springer.com/article/10.1007%2Fs11440-021-01441-0 and https://link.springer.com/article/10.1007%2Fs11440-021-01435-y). […] -
sand liquefaction modelling in Anura3D
Daniel Brox||Constitutive Modelling|0 |Views 504
Beginner level question for this forum – Trying to replace a Mohr-Coulomb model of sand in an Anura3D simulation with a material model which accurately describes sand liquefaction. References I’ve […] -
CEL analysis using hypo plasticity Vumat
abd Elfattah||Constitutive Modelling|8 |Views 4,830
Greetings i used interface Vumat with Umat for simulating CEL problem, after 50% of analysis, i got the error as “Excessive incremental rotation of the elements in element set ” […] -
Animating Soil Models – eLearning Project
Gertraud Medicus||Constitutive Modelling|0 |Views 5,045
Dear all, I am currently writing a proposal for a (small & hopefully nice) eLearning project: Within the project, I would like to create animations related to constitutive modelling. I […]
Search SoilModels Website
Recent posts
- Degradation ( disturbance ) of hypoplastic clay 23.4.2024
- Degradation ( disturbance ) of hypoplastic clay 23.4.2024
- Paper of Coulomb, C. A. (1773) 15.4.2024
- ABAQUS UMAT of hypoplastic clay model 6.4.2024
- Prague Geotechnical Days 2024 “Geotechnical monitoring” and 30th jubilee Prague Geotechnical Lecture by prof. Eduardo Alonso 5.4.2024
- UMAT for Creep-SCLAY model. 1.3.2024
- Cyclic tests with Triax element test driver 14.2.2024
- SUMMER SCHOOL ‘Numerical Modelling in Geotechnical Engineering’, Innsbruck – July 22nd-26th, 2024 1.2.2024
- COURSE IN SOIL MODELING – NTNU, Trondheim – October 14th to 18th, 2024 21.12.2023
- MSE walls design in Plaxis 11.12.2023
- sand liquefaction modelling in Anura3D 8.12.2023
- BCV bentonite experimental and modelling datasets 14.11.2023
Recent Comments
- KHA DIDJA on Animating Soil Models
- Jh Xue on Undrained Tests with Clay Hypoplasticity Intergranular
- Zhentao Liu on Problem in simulating CPT using SANISAND04
- Gertraud Medicus on ABAQUS UMAT of hypoplastic clay model
- Chen Zhiming on Download Package of Charles University Implementation of High Cycle Accumulation Model
- Konstantinos Chatzis on Cyclic tests with Triax element test driver
- Abhay Pratap Singh on Cyclic tests with Triax element test driver
- Giovanni Ciardi on Cyclic tests with Triax element test driver
- Konstantinos Chatzis on Cyclic tests with Triax element test driver
- Ismail Khan on Cyclic tests with Triax element test driver
- Kanika Lamba on Cyclic tests with Triax element test driver
- Arie Koot on How to model the settlement in soil due to water drawdown.
- Konstantinos Chatzis on Cyclic tests with Triax element test driver
- Jose Duque on Cyclic tests with Triax element test driver
- MohamadReza Kamali on How to model the settlement in soil due to water drawdown.
- Leo Alibert on MSE walls design in Plaxis
- Ignacio Zuloaga on MSE walls design in Plaxis
- Giada Orlando on Problem with VUMAT interface
Dear Arslan,
You should define the appropriate number of state variables (depvar), please look into the description of the VUMAT interface, besides you need the definition of the parameter 16 in the hypoplastic model, which is the initial void ratio.
Hello, I am learning the penetration simulation of spudcan in hypoplastic soil recently, can you share the cae or inp file of this model for me to learn,my mail address is wdjmcyq@163.com
thank you very much!